Printing methods for packaging bags: a buyer's comparison
Screen, heat transfer, gravure, flexo, offset and foil each solve a different problem. Compare the main bag printing methods by setup cost, volume and artwork requirements.

Printing decides whether a bag looks like a branded product or a giveaway. The method your supplier recommends should follow from the material, the artwork and the order volume — not the other way around. This guide compares the main methods used for packaging bags and the tooling each one needs.
Screen printing: flat colour on non-woven
Screen printing pushes ink through a mesh screen, one screen per colour. It is the most common method for plain non-woven bags because the thick ink layer stays visible on textured fabric. The practical limit is four to six colours; gradients and photographs are not realistic. A screen per colour keeps setup moderate, so screen printing is economical from a few hundred pieces per design.
Heat transfer: detail on non-woven
Heat transfer prints artwork onto a carrier film and transfers it under heat and pressure. It handles fine detail, small text and multi-colour images that screen printing cannot, and adheres well to non-woven. Setup costs more, which suits larger runs or genuinely complex artwork.
Gravure and film lamination: photographic quality
For laminated non-woven and printed PE, artwork is printed by gravure onto film that is then laminated to the material. Gravure gives dense, consistent colour and fine detail across long runs — the retail campaign standard. Each colour needs a cylinder, so tooling is significant: gravure makes sense at high volume, not for trials.
Flexography: printed PE bags
Flexo uses flexible plates on a roll-fed press and is the standard for PE shopping bags, typically in two to six colours. Plates cost less than gravure cylinders, so flexo suits mid-size runs; registration is less precise, so avoid very fine line work.
Offset litho, foil and decorative finishes
Cardboard gift bags are often printed by offset litho on sheets, then laminated to board and die-cut. Offset gives sharp text and photographic colour at small-to-mid volumes. Hot foil, spot UV, embossing and matte or gloss lamination are applied after printing; each finish adds a production step but can lift perceived value more than a heavier board would.
Comparing the methods
| Method | Best for | Colours | Tooling | Volume sweet spot |
|---|---|---|---|---|
| Screen | Plain non-woven | 1–6 | Screen per colour | 50–20,000 |
| Heat transfer | Detailed non-woven | Full colour | Transfer film/plate | 1,000+ |
| Gravure | Laminated non-woven, PE | 4–10 | Cylinder per colour | 30,000+ |
| Flexo | PE bags | 1–6 | Plate per colour | 3,000–100,000 |
| Offset | Cardboard gift bags | CMYK + spot | Plate set | 1,000–50,000 |
| Foil / UV / emboss | Premium finishes | Spot | Die per finish | Setup per finish |
Colour control: agree it before production
Agree the colour reference first: Pantone numbers for solid brand colours, CMYK for photographic areas, and a tolerance — ΔE 2 is a common target for brand colours. Ask for a physical proof or press sheet rather than a PDF, because screens and paper shift perception. Agree the light source used for approval too: a colour can pass under one lamp and fail under another.
Artwork checklist
- Logos in vector format (AI, EPS or PDF)
- Fonts outlined or supplied
- 3 mm bleed on all sides
- CMYK and spot colours clearly separated
- Barcode quiet zones respected
- Dieline supplied and aligned
- Images at 300 dpi at final size
- Separate layers for white ink, foil and spot UV
Setup costs and minimum order
Tooling drives the minimum order more than labour does. A screen costs far less than a gravure cylinder, so a screen-printed run can start at 50 pieces while a gravure campaign realistically starts at 30,000. For a small trial, choose a low-setup method, then move to heavier tooling once the artwork is final.
Which method should you choose?
- Plain non-woven bags: screen printing for one to four flat colours; heat transfer when the artwork has detail.
- Retail campaigns with photography: gravure-printed lamination, planned for high volume.
- PE shopping bags: flexo, with a reinforced die-cut handle.
- Gift bags: offset litho plus lamination, with foil or spot UV for the logo.
Send your artwork and target quantity and we will confirm which method fits your material and volume — and where a cheaper setup still meets the brief. Request a print recommendation.
Figures in this guide are typical ranges from our own production. Exact MOQ and lead time depend on bag size, material, print method and season — confirm both against your specific specification.
About the author
Baige Packaging production team
Production team, Baige Packaging
Material sourcing, printing, QC and export packing for custom bag orders. Every guide is checked against real production specifications and updated when a standard changes.
Related guides.
The next decisions most buyers face after this one.

Non-woven vs kraft paper vs white cardboard bags: which should your brand print on?
Non-woven, kraft paper and white cardboard can all carry a logo, but they behave very differently in use, print and end-of-life. Compare all three on the criteria that actually decide a packaging project.
Read article
How to choose bag GSM: a practical guide by material
GSM is the first number most buyers ask for, but heavier is not automatically better. Here is what GSM changes in non-woven, kraft, cardboard and PE bags — and how to validate the weight you choose.
Read article
Custom bag MOQ and lead times: what buyers should expect
MOQ and lead time are not fixed numbers — they come from material minimums, printing setup and factory capacity. Here is how both are calculated and how to plan around them.
Read articleRequest a quote
Need a bag built to this specification?
Send your size, material, printing and quantity — we reply with pricing, sampling options and lead time within one business day.